PRAXOS ADVISORY GROUP
Practice Area 11

Hazard Assessment & Analysis

Hazard assessment is where the difference between someone who has seen situations and someone who has only read about them becomes visible. A Job Hazard Analysis conducted by an experienced practitioner identifies exposures that a checklist misses — because the practitioner knows what to look for, not just what the form asks. The same principle applies at every scale, from a single job task to a complex process hazard analysis.

Start a Conversation → All Practice Areas
At a Glance
MethodsJHA · PHA · HAZOP · What-If
Engagement typeProject
CoverageNationwide
Credentials & PracticeCSP · IH · CSHM
Experience30 years cross-industry
Initial callNo charge

The right methodology for the hazard — from routine task analysis to complex process review.

Hazard assessment methodology should match the complexity of what is being analyzed. Applying a HAZOP to a routine maintenance task is overkill; applying a What-If to a covered chemical process is insufficient. Method selection is part of the engagement.

01

Job Hazard Analysis (JHA / JSA)

Task-level hazard identification for routine and non-routine work — breaking jobs into steps, identifying hazards at each step, and documenting the controls required to perform the work safely. Used for training, procedure development, and incident prevention.

02

Process Hazard Analysis (PHA)

Systematic hazard identification for processes with significant injury or release potential — using What-If, checklist, or FMEA methodology depending on process complexity and regulatory requirements.

03

HAZOP Studies

Hazard and Operability studies for complex continuous processes — a structured, team-based examination of process deviations and their consequences, required under OSHA PSM for covered processes.

04

Baseline Hazard Surveys

Facility-wide hazard identification surveys establishing a documented baseline of existing conditions — used to prioritize corrective actions, support insurance reviews, and anchor ongoing program development.

05

Pre-Task Planning

Development of pre-task planning systems for high-hazard work — permit-to-work programs, pre-job safety briefings, and stop-work authority frameworks that give workers the tools to identify hazards before work begins.

06

Risk Ranking & Prioritization

Systematic ranking of identified hazards by likelihood and consequence — establishing a defensible priority order for corrective action that allocates resources to the highest actual risk rather than the most recently reported complaint.

Any organization where the gap between identified hazards and actual controls needs to be closed.

Hazard assessment is foundational — it is the step that every other safety program depends on. Organizations that skip it or do it poorly end up with programs that address the wrong things.

Manufacturers & Industrial Operations

Facilities with process equipment, chemical handling, material movement, and maintenance activities where task-level JHA and process-level PHA are both necessary — and where the quality of the analysis determines the quality of everything downstream.

Construction Firms

Projects with high-hazard activities — excavation, steel erection, confined space entry, energized electrical work — where pre-task planning and documented hazard analysis are both OSHA requirements and genuine risk management tools.

Operations Post-Incident

Facilities that have experienced a significant injury or near-miss and need a credible hazard analysis to anchor the corrective action plan — and to demonstrate to OSHA, insurers, or legal counsel that the response was systematic and defensible.

New Operations or Processes

Facilities bringing new equipment, processes, or chemicals online — where hazard analysis before startup is significantly less expensive than incident investigation and corrective action after one.

Hazard analysis has a sequence. Skipping steps produces gaps that get found the wrong way.

The method and scope are established upfront. Analysis is conducted with the people who actually do the work — not in an office without them.

01.

Scope & Method Selection

Identification of the tasks, processes, or facilities to be analyzed and selection of the appropriate methodology — JHA, PHA, HAZOP, or baseline survey — based on complexity, regulatory requirements, and available resources.

02.

Analysis

Structured hazard identification conducted with subject matter experts and frontline workers — the people who know where the actual exposures are, not just where the procedures say they should be.

03.

Documentation

A written analysis document that records identified hazards, existing controls, residual risk ranking, and recommended additional controls — formatted for use in training, procedure development, and regulatory review.

04.

Corrective Action Support

Assistance prioritizing and implementing the corrective actions identified in the analysis — ensuring the findings produce actual risk reduction rather than a report that sits on a shelf.

Before the engagement begins.

Questions that typically come up when organizations are considering a hazard assessment engagement.

A Job Hazard Analysis (JHA) — also called a Job Safety Analysis (JSA) — focuses on the steps involved in a specific task and the hazards present at each step. It is task-level and typically used for routine and non-routine work procedures. A Process Hazard Analysis (PHA) is a broader examination of a process — the equipment, chemistry, controls, and potential deviations — typically used for processes with significant release or injury potential and required by OSHA PSM for covered processes.
It depends on the scope. A JHA for a single maintenance task may take a few hours. A HAZOP study for a complex covered process may take several days of team meetings plus documentation time. The scope and timeline are established before the engagement begins.
The people who actually do the work. Hazard analyses conducted without frontline worker involvement consistently miss exposures that workers know about — and produce documents that workers do not trust or use. Supervisor and engineering input is also important, but it does not substitute for the people on the floor.
OSHA does not have a specific standard requiring JHAs by name, but hazard assessment is implied by multiple OSHA standards — the General Duty Clause, the PPE standard (1910.132), permit-required confined space entry, lockout/tagout, and others. More practically, the absence of documented hazard analysis is a significant liability in any OSHA inspection or post-incident litigation.

Ready to close the gap between identified hazards and actual controls?

A fifteen-minute call — no charge — to understand your situation and determine whether there is a fit before any commitment is made.

Start a Conversation →